Bjóðum upp á öruggar kortagreiðslur í gegnum Valitor ásamt Netgíró með möguleika á greiðsludreifingu

ChemicalGuys Phase 5 Fiberglass Polish

Verð:
ISK 5.100

Chemical Guys Phase 5 Fiberglass Polish er auðvelt í notkun, polish sem skapar mirror look í einu skrefi . Phase 5 er sérhannað fyrir Fiberglass, Gel Coat og önnur hörð efni og lökk. Það cuttar vel Swirl marks, minni rispur og galla. Þetta háþróaða eins skrefs polish efni skilar gljáa og dýpt eins og fínn polish. Chemical Guys Phase 5 er hannað til að stytta vinnutíma samanborið við hefðbundna tvískipta -aðgerð. Phase mun skila frábærum árangri á broti af tíma af stöðluðum 2 eða 3 mössunar ferli.

Chemical Guys Phase 5 er all in one scratch and swirl remower sem fajrlægir rispur og Swirls marks í einni umferð og skilar af sér mirror like áferð. Þetta háþróaða polish efni byggir á minnkandi svarfefni tækni. Þessar nýja slípiefni cuttar hratt til að fjarlægja swirlmarks, rispur og oxun, en minnkandi svarfefnið endar sem fínt polish eða 2500 grit sanding mark.


  • Hentar mjög vel fyrir Fiberglass, Gel Coat og hörð lökk
  • Eins þreps há glans polish
  • Frábær gljái í einu þrepi.
  • Fjarlægir rispur, swirl marks, water spots og aðrar skemmdir.
  • Hentar fyrir glærur jafnt og einna þátta lakk.
  • Hentar fyrir alla liti.
  • Hentar fyrir rotary og otbital massavélar.




How To Use:

Application by Hand:
Mist desired pad to be used with Chemical Guys polishing Pad Conditioner moisten the foam and reduce friction.
Apply a nickel size amount of Phase 5 polish to the applicator.
It is always recommended to apply polish out of direct sunlight.
Work polish in a back and forth, work in 2 x 2 sq. foot sections until the entire surface is done.

Note: General Hand application of Phase 5 polish by hand will remove light oxidation and minor imperfections while enhancing gloss. Doing the work by hand will not deliver the same superior results achievable with a PC or Rotary. For paint correction, it is always recommended to use a polisher.

Application by Machine:
Mist desired pad to be used with Chemical Guys polishing Pad Conditioner to moisten the foam and reduce friction.
Apply a nickel size amount of Phase-5 polish to the applicator.
Always make sure the surface to be Compounded is clean and dry.
If surface is freshly or recently painted, always allow time to properly cure.
It is always recommended to apply polish out of direct sunlight.
Though product will work great even in the sun, maximum work time is achieved out of direct sunlight.
For light jobs use Lake Country CCS pads orange or green.
For large boats and RVs or larger more oxidized surfaces use a wool or foam polishing pad.
Apply a 4-6 inch line of polish to the surface.
With the polisher turned off, spread the polish over about a 2 x 2 sq. ft. area.
polish at 1200-1800 RPM on rotary polisher or 5000-6000 OPM for Dual-Action polisher.
Work area slowly across and then up and down the area.
Always double check your work after several passes to assure proper results.
Wipe surface area with a lightly damp microfiber towel.
Always apply a wax or sealant after Compounding or polishing.
Chemical Guys recommends Jet Seal for maximum protection, durability and wet mirror shine.

Specifications
Part Number GAP11416
UPC 811339027831
Size 16 ounces // 473ml
Top Flip cap
Grit range 1500 - 2500
Flaking Nominal
Silicone-free Yes
Wax-free Yes
Body shop safe No
Hand application No
Machine application Yes
Safe for clear coat Yes
Safe for light color cars Yes
Safe for dark color cars Yes

Additional Information

SKUGAP11416